Well Service Engines C9 ACERT™ (Dry Manifold)

Product Specifications for C9 ACERT™ (Dry Manifold)

C9 ACERT™ (Dry Manifold) Standard Equipment

Air Inlet System

• Turbocharger, separate circuit (SCAC) or remote (REMAC) aftercooler

• Single, right-side, center-mounted turbo with water-cooled turbine housing

• Air inlet 101.6 mm (4 in) connection type

Control System

• Electronic governing, PTO speed control

• Programmable ratings

• Cold mode start strategy

• Automatic altitude compensation

• Fuel cooled ECU

• Power compensation for fuel temperature

• Programmable low and high idle

• Electronic diagnostics and fault logging

• Programmable monitoring system (engine speed, temperature, pressure)

• J1939 broadcast (diagnostic and engine status)

• Electronic installation kit (connectors, PINS, sockets) (nonhazardous environment only)

• Certified electrical control system (hazardous environment only)

• Derated engine: automatic ambient temperature compensation

Cooling System

• Thermostats and housing, RH forward-facing outlet — 51 mm (2.01 in) connection

• Jacket water pump — belt-driven, centrifugal

• Water pump — inlet RH facing downward 63 mm (2.48 in)

Exhaust System

• Exhaust manifold — water-cooled

• Single, center right-side mounted turbo with water-cooled turbine housing

• Rear facing turbo exhaust 81.8 mm (3.22 in.) connection, non V-band clamp

Flywheels and Flywheel Housings

• Mandatory selection of: SAE No. 1 or SAE No. 2 flywheel and housing, SAE standard rotation

Fuel System

• HEUI fuel system

• Fuel filter — secondary, LH (2-micron high performance)

• Fuel transfer pump — left front

• Fuel priming pump — left front

Lube System

• Crankcase breather — LH

• Crankcase fumes disposal with integrated service indicator, LH

• Oil cooler — RH

• Oil filter — RH

• Oil pan — front sump

• Oil filler — top mounted

• Oil level gauge — LH side

• Oil pump — gear-driven

• Oil valve sampling

• Preservation of turbocharger, flywheel, and crankcase

Power Take-Offs

• Crankshaft drive pulley — 2 grooves, 190 mm (7.5 in) diameter, 22.3 mm (7/8 in) wide

General

• Vibration damper

• Lifting eyes

• Automatic variable timing — electronic

• Literature

Mandatory Options

• Flywheel housing and flywheel

• Throttle position sensor and/or throttle control (non-hazardous environment only)

• Primary filter/water separator

• Turbo orientation

C9 ACERT™ (Dry Manifold) Optional Equipment

Air Compressor

• Air compressor governor

Air Inlet System

• Air cleaners

• Precleaner

• Air inlet elbow

• Air shutoffs

Charging Systems

• Charging alternators

• Alternator mountings and pulleys

• Alternator belt tensioner

Cooling System

• Radiators

• Radiators

• Fans f/u/w radiator packages

• Coolant level sensor

• Fan drive mountings, adapters, pulleys

• Vee belts for customer-supplied radiators

• Suction fans and blower fans

• Water inlet elbows

• Dry charge coolant conditioners

Emissions Certification

• IMO Certification

Exhaust System

• Flexible fitting

• Turbocharger exhaust outlet adapters

• Elbows, flange, pipes, clamp

• Rain caps

• Manifolds

• Mufflers

Flywheels and Flywheel Housings

• Crankshaft seal

Fuel System

• Flexible fuel lines

• Water separator and fuel filters

• Fuel cooler

Instrumentation

• Gauges and instrument panels

• Interconnect harnesses

• Voltmeters

• Gauge mounting

• Ammeter

Lube System

• Oil pan

• Drain and cover

• Oil level gauges

• Remote oil filter

• Oil fillers

• Lubricating oil

• Fumes disposal

• Fumes disposal mounting

Mounting System

• Structural steel base

• Front and rear engine supports

Power Take-Offs

• Enclosed clutch

• Clutch supports

• Flywheel stub shaft

• Hydraulic pump drives

• Hydraulic gear pumps

• Pulley

Starting System

• Starting aids

• Electric starting motors — 12V and 24V

• Battery sets — 12V and 24V (dry)

• Battery cable

Transmission Arrangement

• Transmission cooler

General

• Tool set